Enviro Maxx-M Especificaciones

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFE

Figure 10: Corner Installation. Installationmobile home inStallation:4"(10cm)4"(10cm)Fresh Air IntakeWall thimblemanufacturedby pellet ventm

114" (100mm)Exhaust Tube4" (100mm)Vent PipeWall Thimble45o Elbow or Termination CapHigh Temperature RTV Silicone Required3" (80mm)Inlet

Installation7. Push the stove straight back, leaving a minimum of 4” (10 cm) clearance from the back of the stove to the wall. Seal the vent pipe to

Wall framingWall thimbleTermination capVertical section of vent pipeClean out teeWall strap90°elbowHorizontal frame for thimbleInstallationrecommended

14InstallationoutSide vertical inStallationS:To accomplish an outside vertical pipe installation, follow the “hOrizOntAl exhAust thrOugh WAll instAllA

2 ft(61 cm)Rain Cap (ensure cap is at least 3ft (91cm) above the roof at the lowest point)Roof FlashingRoof RafterFire Stop with Support CollarCeiling

Existing FireplaceClean Out TeeFireplace Damper LocationRain CapSeal PlateVent Pipe (single wall stainless flex pipe or PL vent)Existing Masonary Flu

17InstallationSlider/damper Set-up:This is used to regulate the airflow through the pellet stove. The slider damper should be set by a trained technic

TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly.

19Troubleshooting• Exhaust Temperature Sensor failure. Bypass sensor located on Exhaust Blower, if stove now operates properly, the unit may require

2Safety Warnings & Recommendations...3Installation...

Troubleshooting8. Ignitor - the pellets will not light. NOTE: The ignitor should be bright orange in color. • Everything else in the stove operates b

21Wiring Diagram

Parts List22ITEM # DESCRIPTION PART #1 SLIDER DAMPER SET COLLAR KIT 50-10682 AUGER WITH PADDLES 50-11613 BURN POT SCRAPER TOOL 50-12544 LEVELING LEGS

23Parts ListITEM # DESCRIPTION PART #38 AGITATOR DRIVE SHAFT W SPROCKET 50-169839 MOTOR DRIVE SPROCKET 50-170040 .250 SPRING PIN 50-170141 AIR PUMP 5

Parts Diagram 24102771265664284253375436582524296968122357261454849416344467556365513843392019232114151611 1213329663157305952463347171820MAXX-M PARTS

25WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to

26WarrantyExclusions and Limitations:1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint. 2. This Warranty exclu

27Warranty17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surf

28NAME OF OWNER:_________________________________________ADDRESS:_____________________________________________________________________________________

3Safety Warnings & Recommendations* This manual is designed for the technician in conjunction with the owner’s manual. *Please read this entire Te

4Safety Warnings & RecommendationsELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded elect

5Installationrating label location:The rating label is located on the inside of the hopper lid.deciding Where to locate your pellet appliance:1. Do no

InstallationdimenSionS & SpeciFicationS:62113/16" (554mm)1515/16"(404mm)219/16"(548mm)411/4"(1047mm)4113/16"(1063mm)2313/

7InstallationclearanceS to combuStibleS:12"(30.5cm)4" (10cm)4" (10cm)Side WallBack WallAdjacent WallThese dimensions are minimum cleara

8hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.3. Termination must exhaust above the inlet el

InstallationoutSide FreSh-air connection:This Heater must have adequate air for proper combustion in the room that it is installed.A Fresh-air intake