Enviro EF3Bi Instrucciones de operaciones

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCESHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED P

10Installation of firebox backing:• Install the side panels in place. Insert center panel, hold the panels in place• Install the top rod by sliding i

11InstallationDeciDing WheRe to locate youR Pellet aPPliance:1. Check clearances to combustibles.2. Do not obtain combustion air from an at

InstallationDimenSionS - fReeStanDing:20 15/16"(532 mm)22"(559 mm)30 1/4"(768 mm)23 3/4"(603 mm)21 15/16"(557 mm)12 11/16&quo

13InstallationcleaRanceS to combuStibleS - fReeStanDing:When installing this unit on a combustible floor (for example linoleum, hardwood f

14InstallationcleaRanceS to combuStibleS - built-in heateR:Refer to Figures 11 and 12.Side wall to unit - 8 inches (20.3 cm)Mantel proje

15Air Supply InletGas MeterRestriction Zone(Termination not allowed)Termination CapGGOpensOpensOpensDFBBAIHKGGLCEhot enough to cause burns if touched

A Fresh-air intake is strongly recommended for all installations. Failure to install intake air may result in improper combustion as well as

17Figure 21: Corner Installation. Installationmobile home inStallation - fReeStanDing:1" (2.5cm)1"(2.5cm)6"(15 cm)Floor ProtectionFresh

InstallationhoRizontal exhauSt thRough Wall inStallation - fReeStanDing:Vent installation: install vent at clearances specified by the vent manufactur

19Installation10. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outsid

Table of Contents2Introduction...

InstallationinSiDe veRtical inStallationS - fReeStanDing:1. Choose a stove location that is ideal. See the section “deCiding Where to loCate your pe

21InstallationNon-combustiblefloor protection.Existing floor(combustible)6"(15cm)Rain capFlashing24"(61cm)1"(2.5cm)Tee withcleanoutFres

Installation Rain capStorm collarSeal plate (cover plate)Existing masonry flueVent pipe (single wall stainless flex pipe or solid PL vent)Fireplace d

23Floor ProtectionCombustible FloorMasonry FireplaceMin 6" (150 mm)Rain CapSteel Plate or FlashingFlexible or Rigid 6"Stainless Steel LinerM

Non-combustiblefloor protection.Existing floor(combustible)6"(15 cm)3" (7.5 cm)PedestalWallthimbleFresh airintakeRodentmesh cap45°elbow12&qu

Installation25Figure 34: Corner brackets for trim.Figure 35: Two pieces of corner bracket.4. Plug the wiring harness into the control panel (see Figur

InstallationSliDeR/DamPeR inStallation:This is used to regulate the airflow through the pellet stove.1. Remove the slider rod (short rod with

27TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperl

Troubleshooting● Check Vacuum levels in the exhaust channel by bypassing the Vacuum Switch, then remove the Vacuum hose from Vacuum Swi

29Troubleshooting6. The auger motor will not function normally.● If the Auger gear box does not turn but the motor’s armature does try to spi

3IntroductionPellet Quality:Pellet quality is important, please read the following:Your enviro pellet stove has been designed to burn wood pellets onl

8. The 200°F (93°C) high limit temperature sensor has tripped.● Reset the sensor and determine the cause - was it convection blower or 160°F (71°C) t

31Wiring DiagramYellowYellowPurplePurpleOrangePowerCordBrownBrownRedIgnitor120oF (49oC)Ignitor Temperature Sensor160oF (71oC)Convection TemperatureSen

Parts ListReference NumberDescription Part NumberFreestanding Fan Controller Knob EC-040Power Cord - 115V EC-042Window Channel Tape 60” (1.5 m) EC-058

33Reference NumberDescription Part Number17 Freestanding Pedestal Complete EF-139Ignitor Tube Only EF-140Pellet Stove Cleaning Brush EF-15618 Freestan

Parts ListReference NumberDescription Part Number39 Fireplace Insert Ash Pan Drawer With Latch 50-178940 Freestanding Stove Top 50-179241 Fireplace In

35Parts Diagram - Components91056302281323111214252429324733341EF3 - Components (115V)February 2008

Parts Diagram - Steel57565538212374350494732273917511618825542635444220453631465049534041154819EF3 - Steel Components (115V)February 200836

37WarrantySherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to

38WarrantyExclusions and Limitations:1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint. 2. This Warranty exclu

39Warranty17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surf

4IntroductionimPoRtant Safety Data:Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follo

40The following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:_______________________________

5IntroductionASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be on a non-co

6Operating Instructionsautomatic Safety featuReS:Your pellet Stove has the following safety features:A. The stove will shut off when the fire

7Operating InstructionsoPeRating youR Pellet Stove:Figure 3: Dial-A-Fire control panel. 1. Check and fill hopper with pellets.2. Make sure unit is p

8Routine Cleaning and MaintenanceNOTE: Do not use abrasive cleaners to clean the surface or any part of the stove.The following should be inspected pe

9ASH PAN (2-3 days)Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good ind